Door and Window Installation in Garner, NC
Licensed and insured, about 15 minutes from our base, with a fixed written price before any work starts.
Garner holds a lot of 1960s to 1980s brick ranches, which are some of the best value renovations in Wake County. Solid framing, generous lots, and interiors built around small closed rooms that open up beautifully once the right wall comes out.
That is the ground every door and window installation project in Garner starts from. Entry doors, patio sliders, interior doors and replacement windows set plumb, flashed properly and sealed against Carolina storm driven rain.
What the price covers
- Removal and disposal. Old doors, sashes and frames removed carefully to avoid damaging siding or interior trim you are keeping, hauled off the same day.
- Flashing and sill pan installation. A sill pan or flashing tape system that sheds water out and away from the framing, installed before the new unit goes in rather than relying on caulk alone.
- Setting, shimming and fastening. Units set plumb and square, shimmed at the correct points, and fastened per the manufacturer instructions so the frame does not rack under its own weight over time.
Door and Window Installation in Garner, in practice
Homeowners in Garner often assume a window replacement means tearing the wall open, and it usually does not. An insert window fits inside the existing frame and trim, which is faster and less invasive, but it only works when that old frame and sill are still structurally sound and square. When the frame has rot or the opening has shifted, a full frame replacement is the honest recommendation even though it costs more and takes longer. Entry doors have a smaller version of the same problem: an adjustable threshold and the correct sweep close the gap at the bottom without dragging, and get overlooked far more than the door itself. Patio sliders in Wake County houses usually need adjusted rollers and a cleaned track before full replacement.
Most window and door problems trace back to the opening rather than the unit itself. A house in Garner built more than thirty years ago has usually settled a little, which means the rough opening is no longer plumb, level or square even if it started that way. Setting a new unit into that opening without correcting it forces the frame to twist, and a twisted frame binds a door or leaves a window that will not latch fully. We shim to true plumb and square at every corner rather than to the existing framing, and install a sill pan under the unit so any water past the exterior seal drains back out instead of sitting on bare wood at a Wake County crawl space or slab edge.
Free Estimate
Garner homeowners: tell us about the project and we will put a number in writing.
What Garner homes need
Garner holds a lot of 1960s to 1980s brick ranches, which are some of the best value renovations in Wake County. Solid framing, generous lots, and interiors built around small closed rooms that open up beautifully once the right wall comes out.
Permits for structural, plumbing and electrical changes go through the Town of Garner Inspections Department. We file them, schedule the inspections and meet the inspector, so the work is on the record when you eventually sell.
We work across Vandora Springs, Heather Hills, Forest Ridge, Adams Point and the rest of Garner, and we are about 15 minutes from our base.
Everything we do in Garner
How a Garner project runs
Four stages, each finished before the next begins. Typical duration is 1 day to 2 weeks.
Measure and inspect the opening
We check plumb, level, square and the condition of the framing and sill before ordering anything, since a bad measurement means a bad fit no matter how good the unit is.
Order and confirm lead time
Doors and windows are built to spec, so we confirm sizes and options before ordering and set a realistic install date around the actual lead time rather than a hopeful one.
Remove, flash and set
Old unit comes out, the opening gets corrected and flashed, and the new door or window is set plumb and square with the correct fastening and insulation.
Trim, seal and adjust
Trim goes back on, gaps get sealed, and every door and slider gets adjusted and tested through a full open and close cycle before we call it done.
Questions from Garner homeowners
Do older homes in Garner need full frame window replacement?
Often, but not always. We inspect the existing frame and sill before recommending it. Sound framing in a Garner house can sometimes take an insert window, which costs less and disturbs the surrounding trim and siding far less.
What door and window sizes fit Garner openings best?
Openings in Wake County vary a lot by build era, from narrow 1970s ranch openings to wide production builder units from the 2000s. We measure the actual opening rather than assuming a stock size and order to match it.
Do you handle patio slider repairs in Garner, not just full replacements?
Yes. A dragging or hard to lock slider in a Garner home is usually a roller or track problem. We assess it as a repair first and only recommend replacement when the frame or seal has actually failed.
What insulation do you use around the jambs?
Low expansion foam or backer rod and sealant, matched to the gap size and the manufacturer specification. Standard high expansion foam can bow a jamb inward and cause a door or window to bind right after installation.
What it usually costs
Door and Window Installation in Garner generally runs between $1,400 and $26,000, depending on size and finish level. The estimate is free and the number we write down is the number you pay.
Call (919) 335-7730What homeowners say
Pulled straight from our Google Business Profile, and updated as new reviews come in.
Keep looking
The same trade in nearby towns, and the rest of what we do in Garner.
Door and Window Installation nearby
Other work in Garner
Door and Window Installation in Garner
Free estimates across Garner and the wider Triangle, with a fixed written price before any work starts.